Commission Nodes

Once a node is added to MAAS (see Add nodes) the next logical step is to commission it.

To commission, the underlying machine needs to be configured to netboot (this should already have been done during the enlistment stage). Such a machine will undergo the following process:

  1. DHCP server is contacted
  2. kernel and initrd are received over TFTP
  3. machine boots
  4. initrd mounts a Squashfs image ephemerally over HTTP
  5. cloud-init runs built in and custom commissioning scripts
  6. machine shuts down

The commissioning scripts will talk to the region API server to ensure that everything is in order and that eventual deployment will succeed.

The image used is, by default, the latest Ubuntu LTS release and should not require changing. However, it can be configured in the 'Settings' page of the web UI by selecting the 'General' tab and scrolling down to the Commissioning section.

To commission, on the 'Machines' page, select a node and choose 'Commission' under the 'Take action' drop-down menu.

commission

You have the option of selecting some extra parameters (checkboxes) and performing hardware tests.

These options include:

  • Allow SSH access and prevent machine powering off: Machines are normally powered off after commissioning. This option keeps the machine on and enables SSH so you can access the machine.

  • Retain network configuration: When enabled, preserves any custom network settings previously configured for the machine. See Networking for more information.

  • Retain storage configuration: When enabled, preserves any storage settings previously configured for the machine. See Storage for more details.

  • Update firmware: Runs scripts tagged with 'update_firmware. See Testing scripts for more details.

  • Configure HBA: Runs scripts tagged with 'configure_hba'. As above, see Testing scripts for further details.

confirm commission

Click the Hardware tests field to reveal a drop-down list of tests to add and run during commissioning. See Hardware testing) for more information on hardware testing scripts.

Finalise the directive by hitting 'Commission machine'.

While a node is commissioning its status will change to Commissioning. During this time the node's network topology will be discovered. This will prompt one of the node's network interfaces to be connected to the fabric, VLAN, and subnet combination that will allow it to be configured. By default, a static IP address will be assigned out of the reserved IP range for the subnet. That is, an IP assignment mode of 'Auto assign' will be used. See the next section for details on assignment modes.

See MAAS CLI for how to commission a node with the CLI.

Once a node is commissioned its status will change to Ready and an extra tab for the node called 'Commissioning' will become available. This tab contains the results of the scripts executed during the commissioning process.

Now that the node is commissioned you may consider creating or applying a tag (see Tags for more on this).

The next step will be to deploy the node. See Deploy nodes.

Post-commission configuration

Once a node has been commissioned, its network interface(s) can be configured. Specifically, when a node's status is either 'Ready' or 'Broken', interfaces can be added/removed, attached to a fabric and linked to a subnet, and provided an IP assignment mode. Tags can also be assigned to specific network interfaces (see Tags for network interfaces).

From a node's 'Interfaces' page, click the menu icon for the interface to be edited and select 'Edit Physical' from the resulting menu:

edit interface

The following window will appear:

configure interface

There are four modes to choose from that determine how an address on the subnet gets assigned when the node is eventually deployed. These modes are selected by clicking on the 'IP mode' drop-down menu.

  • Auto assign: MAAS will assign a random static address (iface eth0 inet static). The pool of available addresses depends on whether the subnet is managed or unmanaged (see Subnet management).

  • Static assign: The administrator will specify a static address using a secondary field.

  • DHCP: A dynamic address will be leased via either MAAS-managed DHCP or an external DHCP server.

  • Unconfigured: The interface will be left unconfigured.

Press the 'Save' button to apply the changes.

See Concepts and terms for the definitions of reserved range types and MAAS CLI - advanced tasks to learn how to change the IP-assignment mode of a network interface using the CLI.

Bond interfaces

A bond interface is used to aggregate two or more physical interfaces into a single logical interface. A bond is created by selecting more than one interface and clicking the now-active 'Create bond' button:

configure setbond

After clicking the 'Create bond' button, the bond configuration pane will appear.

From the bond configuration pane, you can rename the bond, select a bond mode (see below), assign a MAC address to the aggregate device and attach one or more tags.

The interfaces aggregated into the bond interface are listed below the 'Tags' field. Use the 'Primary' column to select the interface to act as the primary device.

configure bond

The following bonding modes can be selected from the 'Bond mode' drop-down menu:

  • balance-rr: Transmit packets in sequential order from the first available slave through to the last. This mode provides load balancing and fault tolerance.

  • active-backup: Only one slave in the bond is active. A different slave becomes active if, and only if, the active slave fails. The bond's MAC address is externally visible on only one port (network adapter) to avoid confusing the switch.

  • balance-xor: Transmit based on the selected transmit hash policy. The default policy is simple. This means packages are selected by an XOR operation between the source MAC address and the resultant XOR between the destination MAC address the packet type identifier, modulo slave count.

  • broadcast: Transmit everything on all slave interfaces. This mode provides fault tolerance.

  • 802.3ad: Creates aggregation groups that share the same speed and duplex settings. Utilises all slaves in the active aggregation according to the IEEE 802.3ad specification.

  • balance-tlb: Adaptive transmit load balancing, channel bonding that does not require any special switch support.

  • balance-alb: Adaptive load balancing, includes balance-tlb plus receive load balancing (rlb) for IPV4 traffic. Does not require any special switch support. The receive load balancing is achieved by ARP negotiation.

Press the 'Save' button when you're done.

Note: The MAC address defaults to the MAC address of the primary interface.

Bridge interfaces

A bridge is created by selecting an interface and clicking the now-active 'Create bridge' button. A form will appear that will allow a MAC address, STP, and a tag to be configured.

configure bridge

Press the 'Save' button when you're done.

Pro tip: A network bridge may be useful if virtual machines or containers are to be put on the node.

See CLI Interface Management for details on how interfaces can be configured from the command line.